Search Result

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Search Results: 36 results in 0.0033 seconds.

John A. Ross started a topic Front suspension bracket - mod front bracket nut/bolt to ease installation / removal

in F. Front Suspension, Hubs & Stub Axles

26th April 2020, 08:15 AM
Front suspension bracket - mod front bracket nut/bolt to ease installation / removal

As come up in another thread by Bob and a further correction by Mike

Note - Early cars...

See more | Go to post
3 likes
John A. Ross started a topic Renew heater hoses - not as bad as it sounds

in A. Cooling System

24th April 2020, 09:19 PM
Renew heater hoses - not as bad as it sounds

After a Facebook reply I decided to add it here as well so I don't have to repeat it again.
...

See more | Go to post

Last edited by John A. Ross; 24th April 2020, 09:23 PM.
2 likes
moose549 started a topic Bias pedal boxes

in Moose Corner - Competition Replacement Parts And Advice From Mike Dent

20th April 2020, 07:38 AM
Bias pedal boxes

...

See more | Go to post
Dave Lane started a topic Gear selector shaft

in Daves Corner - Nods Mods Collection

19th April 2020, 09:20 PM
Gear selector shaft

Knackered , worn or rusty gear-linkage rod , no probs if you can braze - its only 1 inch diameter rod...

See more | Go to post
4 likes
moose549 started a topic Competition spec gearbox mounts

in Moose Corner - Competition Replacement Parts And Advice From Mike Dent

18th April 2020, 03:40 AM
Competition spec gearbox mounts

Competition Gearbox Mounts £140 pair delivered to UK mainland Motorsport tried and proven.
...

See more | Go to post
2 likes
John A. Ross started a topic Handmade special tools we make - clutch slave cylinder piston retainer

in S: Special Tools

15th April 2020, 10:44 PM
Handmade special tools we make - clutch slave cylinder piston retainer

Again something useful pushes slave cylinder piston back to reduce air in piston (use Dave Lane...

See more | Go to post
1 like
John A. Ross started a topic Handmade special tools we make - rear drive shaft pusher / crank pulley puller

in S: Special Tools

15th April 2020, 10:41 PM
Handmade special tools we make - rear drive shaft pusher / crank pulley puller

Hand made special tools we end up making

Rear drive shaft pusher as drive shafts always...

See more | Go to post
moose549 started a topic Dampers

in Moose Corner - Competition Replacement Parts And Advice From Mike Dent

15th April 2020, 03:17 PM
Dampers

Full car set of competition dampers based on what was considered the ultimate damper in its day the...

See more | Go to post
4 likes
John A. Ross started a topic Owners Other Cars - Anything else interesting in the garage ? Want to share ?

in Everything Non Imp - BUT BE POLITE !!

15th April 2020, 11:45 AM
Owners Other Cars - Anything else interesting in the garage ? Want to share ?

Owners Other Cars - Anything else interesting in the garage ?
Want to share ?

Imp...

See more | Go to post
moose549 started a topic Roller release bearing mod.

in D. Clutch And Hydraulics

15th April 2020, 06:39 AM
Roller release bearing mod.

I can supply a fork and bearing ready to fit to your car the forks are cleaned, welded to add strength...

See more | Go to post
2 likes
John A. Ross started a topic Replacement screw in fuel senders - Alternative

in C. Fuel & Exhaust System

12th April 2020, 11:55 AM
Replacement screw in fuel senders - Alternative

At the time i was looking for fuel senders i found that out the 7 or so I had lying around all had issues...

See more | Go to post
1 like
moose549 started a topic Rear back plate problems

in K. Brakes - Front Rear And Hand Brake

1st April 2020, 07:24 PM
Rear back plate problems

Many people jump to disc brakes Thinking more modern is better, in some ways it is less adjustments...

See more | Go to post
1 like
John A. Ross started a topic 45D4 Distrinutor in bits - in case you want a look

in N1. Electrical System - Start, Charge, Ignition

27th March 2020, 08:08 PM
45D4 Distrinutor in bits - in case you want a look

45D4 Distrinutor in bits - in case you want a look

Bottom pin driven out and removed, inner...

See more | Go to post
1 like
Dave Lane started a topic Battery clamp

in Daves Corner - Nods Mods Collection

23rd March 2020, 05:54 PM
Battery clamp

Ever noticed that modern 037 / 038 batteries dont fit with the hooked satays too well ??

...

See more | Go to post
2 likes
Dave Lane started a topic Water Heated washers

in Daves Corner - Nods Mods Collection

19th March 2020, 08:30 PM
Water Heated washers

Heater part is dead simple , just a length of 15mm copper pipe with some copper brake pipe wound around...

See more | Go to post
3 likes